2737
Strips-Multi-sensor
Strips, the ultra-thin multi sensor is now available in two new sensor models, Strips Drip and Strips Comfort. Drip and Comfort join Strips Guard, the thinnest magnet sensor in the world detecting if your windows are open and closed invisibly since 2015.
Strip Drip sends an alarm signal if it detects a water leak. Its unique design allows it to be easily placed almost everywhere, including most places other sensors simply can’t fit. With soaking pads integrated in the mounting plate even small amounts of water will be detected. The built-in temperature sensor gives the possibility to combine the leakage alarm with a freeze alarm. There is also a built-in ambient light sensor that may be useful in special applications.
Strips Comfort is a very accurate temperature and ambient light sensor. The unique design and mounting plate makes it easy to place almost invisibly in your home to measure temperature or control heating, air conditioning and even windows blinds which are connected to your Z-Wave smart home system.
All Strips products can be used both in-doors and out-doors and the integrated custom battery gives Strips an expected lifetime of up to 10 years. For you, this means no hassle needing to change or charge batteries in your Strips sensors for the lifetime of the products!
Ambient light, Water Leakage & Temperature: Sensor for detection of ambient light, water leakage (flood sensor) including temperature sensor. The product will be packaged in different kits together with the mounting devices to support the ambient light use case or the water leakage use case.
Sensative
11 02 011
ZC10-18015953
HW: 1 FW: 0.03:00.03
ZM5101
6.51.10
Routing Slave
Multilevel Sensor
Reporting Sleeping Slave
0x019A
0x0003
0x000A
CEPT (Europe)
0x0D01
0x0D01
https://Products.Z-WaveAlliance.org/ProductManual/File?folder=&filename=Manuals/2737/Strips_Comfort_Drip_zwave_EU.pdf
Set your controller to add mode (see your controller’s manual). Follow the instruction for Wake up. A long LED blink indicates that the add/remove was successful.
Set your controller to remove mode (see your controller’s manual). Follow the instruction for Wake up. A long LED blink indicates that the add/remove was successful.
You may need to reset Strips if your Z-Wave controller is missing or not responding.
Follow the instructions for “Wake up”, but on the 3rd repetition, leave the magnet at the rounded edge for 10 seconds. A long LED signal indicates success.
Wake up Strips manually for Z-Wave communication. Place the magnet at the rounded edge. When the LED blinks, move the magnet away. Repeat twice within 10 seconds.
2018-01-11T19:15:17.151241
https://products.z-wavealliance.org/ProductImages/Index?productName=ZC10-18015953
Sensors
Association Group Information V1
COMMAND_CLASS_ASSOCIATION_GRP_INFO
Association V2
COMMAND_CLASS_ASSOCIATION_V2
Battery V1
COMMAND_CLASS_BATTERY
Configuration V1
COMMAND_CLASS_CONFIGURATION
Device Reset Local V1
COMMAND_CLASS_DEVICE_RESET_LOCALLY
Manufacturer Specific V1
COMMAND_CLASS_MANUFACTURER_SPECIFIC
Notification V4
COMMAND_CLASS_NOTIFICATION_V4
Powerlevel
COMMAND_CLASS_POWERLEVEL
Sensor Multilevel V5
COMMAND_CLASS_SENSOR_MULTILEVEL_V5
Version V2
COMMAND_CLASS_VERSION_V2
Wake-Up V2
COMMAND_CLASS_WAKE_UP_V2
Z-Wave Plus Info V2
COMMAND_CLASS_ZWAVEPLUS_INFO_V2
Z-Wave Plus Lifeline
1
1
High ambient light report level
3 - 64000
10
4
40000
0
false
false
false
false
0
0
3
64000
Low ambient light report level
1 - 42000
(Must be significantly lower than parameter 10)
11
4
5000
0
false
false
false
false
0
0
1
42000
(Must be significantly lower than parameter 10)
Leakage alarm
0: Off
1: On
12
1
1
0
false
false
false
false
0
0
0
0
Off
1
1
On
Leakage alarm level
1 to 100
(1= almost dry, 100= soaking wet)
13
1
10
0
false
false
false
false
0
0
1
100
(1= almost dry, 100= soaking wet)
Moisture reporting period
0-120: Number of hours between moisture reports
14
1
0
0
false
false
false
false
0
0
0
120
Number of hours between moisture reports
LED alarm event reporting
0: Off
1: On
2
1
1
0
false
false
false
false
0
0
0
0
Off
1
1
On
Temperature & Light reporting frequency
1: Normal
2: Frequent
3
1
1
0
false
false
false
false
0
0
1
1
Normal reporting
2
2
Frequent reporting
Temperature reporting
0: Off
1: On
4
1
1
0
false
false
false
false
0
0
0
0
Off
1
1
On
Temperature reporting unit
0: Celcius
1: Fahrenheit
5
1
0
0
false
false
false
false
0
0
0
0
Celcius
1
1
Fahrenheit
Temperature alarms
0: Off
1: On
6
1
0
0
false
false
false
false
0
0
0
0
Off
1
1
On
High Temperature alarm level
-20 to + 60 (degree C)
7
1
60
0
false
false
false
false
0
0
-20
60
Temperature alarm level
Low Temperature alarm level
-20 to + 60 (degree C)
8
1
-20
0
false
false
false
false
0
0
-20
60
Temperature alarm level
Ambient light reporting
0: Off
1: On
2: Report only when levels defined in parameter 10 & 11 are passed
9
1
1
0
false
false
false
false
0
0
0
0
Off
1
1
On
2
2
Report only when levels defined in parameter 10 & 11 are passed
9
2737
false
Air Temperature
Luminance
Moisture
eSelect_Many
Sensors
Sensor types supported by the product.
Select multiple sensors by holding down CTRL as you make selections.
26
2737
false
Built in 3.0V LiMnO2
eEnter_Text
Battery Type
Enter the type (e.g. AA, CR2032, AAA) of the battery/batteries that the product uses.
Enter the battery type designation.
36
2737
false
Heat Alarm
Home Security
Water Alarm
eSelect_Many
Supported Notification Types
Select the Notification Types that the product handles (controllers), or sends (slaves).
Use the CTRL key to select more than one.
18
2737
true
eYes_No
Outdoor Use
Product is suitable for use outdoors.
true
true
false